Skip to content
Privacy Fence Installation in Independence, MO — Cedar, Shadow Box, Vinyl & Value Pine, Built Solid for the Chain-Link Yard

Privacy Fence Installation in Independence, MO — Cedar, Shadow Box, Vinyl & Value Pine, Built Solid for the Chain-Link Yard

In a value-first, chain-link town like Independence, a solid 6-foot privacy fence is a deliberate step up — you're buying an enclosed backyard room off Noland Road and the neighbor's window, not just a way to keep the dog in. The decision is which profile earns it, and how it stands up to the open eastern-plains wind. RKC Wood Care Pros builds pine, cedar board-on-board, shadow box, and vinyl privacy from $20 to $50 per linear foot — posts 36 inches deep in wet-poured concrete below the frost line, shadow box to shed the wind on the exposed east side, runs racked to the older uneven lots, and the first stain coat at 30 days by the same in-house crew. 4.9 stars from 85 Google reviews, 400+ fences across the metro since 2021.

★★★★★
4.9
from 85 reviews
Licensed
& Insured · KS + MO
400+
fences installed
A+ BBB Rated 400+ Fences Installed Since 2021 In-House Stain Crew Free On-Site Estimates
Browse privacy options ↓

GOING SOLID IN A CHAIN-LINK TOWN

The Room, the Wind, and the Old Lot Lines of Independence

1

Going solid when chain link already holds the dog

Independence is a chain-link town by habit — Bingham Estates, Glendale, Santa Fe Trails, and the big older lots all lean on galvanized mesh or an open dog-ear because it's cheap and it keeps the dog in. So a solid 6-foot privacy fence is a deliberate step, not a default: you're buying the enclosed backyard, the block off Noland Road and the neighbor's window, not just containment. We help you decide whether that step earns its cost on your lot before a foot of it gets quoted.

2

Built for the open eastern-plains wind

Push east toward Grain Valley and the neighborhoods thin out into the flat plains, where nothing slows the wind before it reaches a tall fence. A solid six-foot wall out there works like a sail — the whole panel loads onto the posts every time it blows. The fix isn't a beefier post alone; it's the profile. A shadow-box picket pattern leaves a vent between the boards that lets the air through, so the run stops fighting the weather. Which side of the city your lot sits on decides which build we recommend.

3

Solid on Independence's older, uneven lots

The lots here run the full range — flat 1950s ranch yards on a fifth of an acre and 19th-century places on sprawling, rolling ground. On a slope, a privacy panel has to be racked to follow the grade, not stepped, or you leave a triangle gap under every section that defeats the privacy. Where a wide detached-garage drive needs a double gate, the posts get braced 6x6s so the gate doesn't sag its first summer. We lay the run to the ground you actually have.

4

In-house stain that protects what you spent

Spend real money on cedar in a value-first town and you want it to hold — but left bare, cedar silvers out, the boards cup, and the seams spread until daylight shows through what used to be a solid wall. On a privacy fence, the finish isn't cosmetic; it's what keeps the wall closed. Our own crew handles it start to finish: an opening coat about a month after the build, then a refresh on a roughly two-year cycle. No sub, no hand-off — the people who set your posts are the people who keep the boards tight.

CHAIN LINK VS SOLID, SIDE BY SIDE

What a Solid Privacy Fence Buys You That Chain Link Doesn't

What you want from the fence 6-ft chain link 6-ft solid privacy fence
Keep the dog in the yard Does it — the number-one reason most Independence backyards get fenced at all Also does it, and the visual barrier keeps the dog from reacting to everyone who walks by
Block the neighbor's sightline None — mesh sees straight through both ways Full ground-level block from the property line — the whole yard and patio go private
Cut Noland Road & I-70 traffic noise Passes straight through the mesh Panel mass muffles it — the more solid the profile, the more it deadens
Stand up to the open-plains wind Wind slips through the mesh, so the load stays low A solid panel catches it like a sail; shadow box bleeds the gust off and drops the post load
Give you a private backyard room No — the yard still reads open to the street and the neighbors Yes — the enclosed room is the entire reason to go solid
What it runs installed The lowest first cost of any fence $20–50 per foot by profile and material — the trade you make for the room

Chain link wins on first cost and it still holds the dog — the case for going solid is the room, the quiet, and the block, and it's a jump worth making on purpose. The metro-wide breakdown of privacy profiles and the 36-inch standard lives on our Kansas City privacy fence installation page; the neighboring Blue Springs and Grain Valley markets each have their own hub.

THE PRIVACY MENU

Pine, Board-on-Board, Shadow Box & Vinyl — the Independence Profiles

Cedar Board-on-Board privacy fence by RKC Wood Care Pros in Independence, MO

Cedar Board-on-Board

The most-built step up from chain link

Two staggered rows of cedar pickets, front and back, so no light gets through anywhere in the run — the tightest sightline block on the menu and the one most owners land on when they finally retire the mesh. Cedar brings its own rot- and bug-resistant oils, no chemical bath needed. Plan on an opening stain coat about a month out and a refresh every couple of years to hold the boards flat.

  • Price: $22–32/LF installed
  • Lifespan: 15–25 years
  • Maintenance: Re-stain every 2 years
Cedar Shadow Box privacy fence by RKC Wood Care Pros in Independence, MO

Cedar Shadow Box

Both faces finished · sheds the plains wind

Boards mount to alternating sides of the rail, leaving a narrow vent between them — so the fence looks finished from either yard and the wind pours through instead of shoving on it. Out on the exposed lots toward the east side, it's the pattern that stays plumb season after season where a dead-solid wall would take a beating.

  • Price: $25–35/LF installed
  • Lifespan: 15–25 years
  • Maintenance: Re-stain every 2 years
Vinyl Privacy privacy fence by RKC Wood Care Pros in Independence, MO

Vinyl Privacy

Zero stain cycle · popular on rentals

Molded PVC panels stiffened with an aluminum spine in the rails, closed to the ground and identical on both faces, and they never see a brush their whole life. That's the draw for the landlords and rental owners this town has plenty of — real privacy with no maintenance ticket down the road. Heavier panels need posts that can carry them, so we sink the sets to full depth to keep the line true.

  • Price: $36–50/LF installed
  • Lifespan: 30 years
  • Maintenance: None — soap-and-water rinse
Pressure-Treated Pine privacy fence by RKC Wood Care Pros in Independence, MO

Pressure-Treated Pine

The value solid — priced for the budget yard

A solid dog-ear run in treated pine is the budget way to close a yard off — meaningfully cheaper than cedar and the reason so many Independence privacy fences are pine. It's not as stable as cedar, so it wants a seal coat sooner and more often to hold against cup and warp, but for a first fence or a rental where the number matters most, it does the job. We'll price it beside cedar so the trade is yours to make.

  • Price: from $20/LF installed
  • Lifespan: 10–15 years
  • Maintenance: Seal every 1–2 years

WHERE THE PER-FOOT NUMBER COMES FROM

What Moves the Price of an Independence Privacy Fence — Line by Line

Cost driver What it does to the price Typical in Independence
Material choice Pressure-treated pine is the value baseline for a solid run here; cedar is the upgrade; vinyl costs most up front but never needs staining Pine dog-ear from $20 · cedar board-on-board $22–32 · vinyl $36–50
Profile & height A board-on-board overlap or a cap rail costs more than a plain solid dog-ear on the same 6-foot run Board-on-board $22–32 · shadow box $25–35
Open-plains wind build Shadow box is a both-face alternating build — more picket and more layout than a single-side solid panel The default recommendation on the exposed eastern-edge lots
Uneven-terrain layout Racking a run to follow a rolling old estate lot takes more layout time than a straight shot across a flat 1950s ranch yard Handled where the grade calls for it, itemized up front
Old chain-link tear-out Pulling and hauling tired galvanized mesh, its top rail, and the set footings is a line before the new fence goes up Common on the conversion jobs across the older core
Drive gates & stain finish A double-drive gate across a detached-garage drive and the first stain coat are quoted on top of the per-foot run Braced 6x6 gate posts · first coat included on cedar

The material choice sets the floor — pine to close a yard on a budget, cedar as the upgrade most owners land on, vinyl when a rental has to skip the stain call. On top of that, three lines separate an Independence number from a flat suburban quote: the shadow-box build on a wind-exposed east lot, racking on a rolling older lot, and the chain-link haul-off on a conversion — each on its own line, never buried in a per-foot average.

Stained cedar privacy fence cost guide — Independence, MO — RKC Wood Care Pros

INDEPENDENCE PRIVACY FENCE PRICING

What a Privacy Fence Costs in Independence

Cedar Board-on-Board — 6 ft

$22–32

per linear foot installed

Overlapping pickets, full block. The most-requested step up from a chain-link yard.

Cedar Shadow Box — 6 ft

$25–35

per linear foot installed

Both faces finished, with the air gap that sheds the open-plains wind.

Vinyl Privacy — 6 ft

$36–50

per linear foot installed

Solid, no stain schedule, finished both faces. The rental-market favorite.

A solid pine dog-ear anchors the bottom of the range near $20 per linear foot and is why so many local yards go private on a budget; vinyl holds the top near $50 and skips the stain schedule for good. The lot-specific add-ons — a shadow-box wind build, racking on a slope, or hauling off old chain link — land on their own lines, never folded into the per-foot figure. Call (913) 286-1091 to set up a walkthrough.

HOW THE PRIVACY FENCE GOES UP

How a Privacy Fence Install in Independence Actually Happens

1

The walkthrough and a written number

First we come out and read your yard on foot — is there an old chain-link line coming out, how much does the grade roll, and does the lot sit where the east-side wind gets a straight shot. Then you get numbers on paper: linear footage, every gate, tear-out if there's a fence to pull, material, concrete, and the opening stain coat, each on its own line. No ballpark over the phone, no figure scribbled on the back of a card.

2

Layout, utility locate, and clearing the old line

With the material and profile picked, we snap a chalk line to your property pins, mark where the walk gate and any drive gate land, and file the 811 locate so the buried utilities are flagged before anything gets dug. Where we're replacing chain link — common all through the older core — the mesh, the top rail, and every concrete footing come out first, down to clean dirt, so the new fence never gets built around somebody's rusted-out leftovers.

3

Posts three feet down, braced across the wide drives

Every post goes 36 inches into the ground and gets locked with poured concrete on a flared footing, deep enough that the winter freeze-and-thaw has nothing to push against. Wind-exposed east-side runs get the vented shadow-box pattern, rolling estate lots get the panels racked so the boards ride the slope with no gap underneath, and a drive-spanning gate gets doubled-up 6x6 posts so it won't drop out of square. Rails and pickets go on with galvanized ring-shank fasteners that grab and don't back out.

4

The opening stain coat, on our own schedule

Fresh-milled cedar holds too much moisture to soak up stain at install, so the first coat is set roughly a month later — a penetrating semi-transparent finish worked in by hand by the same crew that built the fence. That coat is what stops the boards from cupping apart into see-through gaps, and it's what guards the dollars you put into a fence out here. We keep every job on file and reach back out when the next coat, about two years on, is due.

RECENT INDEPENDENCE INSTALLS

Cedar board-on-board privacy fence in Independence, MO by RKC Wood Care Pros
Board-on-Board · Independence
Natural-finish cedar shadow box privacy fence in Independence, MO by RKC Wood Care Pros
Shadow Box · Independence
Solid dog-ear privacy fence in an Independence, MO backyard by RKC Wood Care Pros
Value Solid · Independence
Open black iron-style fence on an Independence, MO front yard by RKC Wood Care Pros
Open-View Iron · Independence

REVIEWS

What Kansas City Homeowners Say About RKC

4.9 ★ · 85 Google reviews

Every review is on our Google Business Profile — read them there, unedited.

Read all 85 reviews on Google

INDEPENDENCE PRIVACY FENCE QUESTIONS

Privacy Fence Questions Independence Homeowners Ask Most

Dark-finish cedar privacy fence install in Independence, MO by RKC Wood Care Pros

Privacy in Independence

Is a solid privacy fence worth it over chain link in Independence?
It depends on what you're actually after. Chain link is the cheapest way to keep a dog in a yard, and in a value-first town that's why so many backyards already wear it. But mesh gives you zero privacy, no noise buffer, and no wind block. If what you want is an enclosed backyard room — the neighbor's window blocked, the traffic off Noland Road and I-70 muffled, a patio you can actually relax on — that's the case for going solid, and it's a real jump in cost you should make on purpose. We'll walk the lot and tell you straight whether the step earns its price for how you use the yard.
Which holds up better to the wind out toward the east side — solid or shadow box?
Shadow box wins on the open lots. Past the older neighborhoods the ground flattens into plains toward Grain Valley, and a dead-solid six-foot wall there acts like one big sail — every gust lands on the posts. The shadow-box pattern staggers the boards front and back with a vent between them, so most of that wind passes straight through and the run isn't wrestling the weather all winter; you also get a fence that looks finished from both yards. Tuck a lot deep into a sheltered older block and a plain solid panel is fine, and it blocks the view a hair better. It really comes down to where your lot sits.
My lot is older and uneven — will a solid privacy fence gap on the slope?
Not if it's built right. Independence has a lot of rolling, older ground — 19th-century lots and hilly yards where a fence can't just run flat. The wrong way is to step the panels down the grade in level sections, which leaves a triangle gap under each one that defeats the whole point of privacy. The right way is to rack the run — the rails follow the slope and the pickets stay vertical, so the bottom holds tight to the ground the whole way. We rack where the grade calls for it and set the posts deep enough that the slope doesn't work them loose.

Cost, Materials & Upkeep

What does a 6-foot privacy fence cost in Independence?
Pressure-treated pine as a solid dog-ear starts around $20 per linear foot installed — the value baseline that closes a lot of Independence yards. Cedar board-on-board runs $22 to $32, cedar shadow box $25 to $35, and vinyl privacy $36 to $50. A typical 180-foot backyard in cedar board-on-board lands between roughly $4,000 and $5,800. On top of the per-foot number, the lines that move an Independence quote are the shadow-box wind build on an exposed lot, racking on a sloped older lot, and old chain-link tear-out on a conversion — each itemized so you see it before anyone digs. Every estimate is free and written.
Pine, cedar, or vinyl for a privacy fence in Independence?
Pine is the value pick and it's genuinely common here — a solid pine run is the cheapest way to go private, but it's less stable than cedar, so it wants a seal coat sooner and more often to hold against warp. Cedar is the upgrade most owners land on: warmer, more stable, takes an earth-tone stain, and it's the look that ages best. Vinyl costs the most up front but never needs a brush, which is why it's the go-to on the city's many rentals. We price all three on the same written estimate so the choice comes out of the math for your lot, not a pitch.
Does a new cedar privacy fence need staining, and is the first coat included?
Yes to both. Every cedar privacy job we do comes with that opening coat built in, timed about a month after the build so the fresh wood has dried down enough to actually take the finish. From there, a fresh coat roughly every two years keeps the boards flat and the joints tight — and on a privacy fence that's the whole ballgame, because a fence left to weather cups and cracks open into gaps the neighbors can see right through. We handle all of it ourselves, keep your job on file, and reach out when the next coat is due instead of leaving it on you to remember. There's more on our Independence fence staining page.

OTHER INDEPENDENCE FENCE OPTIONS

Weighing Other Materials or Services for Your Independence Fence?

Wood Fence

The full pine, cedar, and composite breakdown — species, grades, and why the value-first market runs pine as everyday wood with cedar as the upgrade.

Explore Wood Fence in Independence →

Chain Link Fence

Galvanized and vinyl-coated mesh — the containment baseline this whole page weighs a solid fence against, and still the practical call on a big open lot.

Explore Chain Link Fence in Independence →

Vinyl Fence

White, tan, and woodgrain vinyl on aluminum-insert rails — zero staining, 30-year life, and the low-maintenance favorite on Independence's many rentals.

Explore Vinyl Fence in Independence →

Ornamental Iron

Powder-coated steel — the decorative, see-through look for the front yard or the estate lot where you want the boundary marked but the view kept open.

Explore Ornamental Iron in Independence →

Aluminum Fence

Rust-free and lighter than ornamental steel — the choice around pools and on the newer builds toward the east side.

Explore Aluminum Fence in Independence →

HOA-Conscious Fencing

The cedar profiles, cap-rail details, and finishes built to read right in the pockets near Blue Springs where covenants do apply.

Explore HOA-Conscious Fencing in Independence →

Fence Repair in Independence

Rotted-post replacement on old 4x4 treated sets, gate re-hangs on sagging wide-drive gates, and storm-damage rebuilds on the open east side.

Fence Repair in Independence →

Fence Staining in Independence

The service that keeps a privacy fence private: in-house cedar staining, first coat at 30 days, re-coat every 2 years by the same crew.

Fence Staining in Independence →

Gate Installation in Independence

Walk gates and double-drive gates on braced welded frames with galvanized hardware — sized for the mower and the detached-garage drives.

Gate Installation in Independence →

Ready when you are

Get a free estimate — we usually respond the same day.

Call (913) 286-1091